Los Angeles County · SCE
Solar Panel Installation in Culver City, CA
Culver City's mix of bungalows and creative-office buildings means we run residential and commercial crews here in the same week, often on the same block.
We are based in Northridge, 18 miles away, and we design Culver City systems around Southern California Edison’s actual rate structure rather than a national average. Permits go through City of Culver City Building Safety. Roofs here are typically composition shingle and flat commercial, which determines the mounting hardware we quote.
Culver City at a glance
- Electric utility
- SCE
- Southern California Edison
- Peak sun hours
- 5.4 hrs/day
- Annual daily average
- Permitting authority
- City of Culver City Building Safety
- Los Angeles County
- Export credit
- ~$0.05/kWh
- NEM 3.0 net billing
- SGIP battery rebate
- Available
- SCE customers may qualify
- From our shop
- 18 miles
- Northridge, CA
A typical Culver City project
What a $300 bill looks like after
Modeled on SCE’s approximate $0.36 per kWh and 5.4 peak sun hours a day in Culver City. Your own numbers will differ — this is the shape of the answer, not a quote.
- System size
- 6.2 kW
- ~14 panels
- Annual production
- 9,713 kWh
- after standard derating
- Annual savings
- $3,135
- at today's rates
- Simple payback
- 11.2 yrs
- $94,944 over 25 years
SCE in plain language
Highest rates in the service area and the toughest export credits — which is exactly why a battery pays for itself fastest here. SCE customers also fund SGIP, so storage rebates are on the table.
You buy at
$0.55
peak, 4–9pm
You sell at
$0.05
exported surplus
That gap is the entire argument for storage in Culver City. A battery lets you use your own midday production during the expensive evening window instead of selling it for a fraction of what you will pay to buy it back.
Run your own numbers
Pre-set for Culver City
Already loaded with SCE rates and 5.4 peak sun hours. Move the slider to your bill.
Step 1
Step 2
Who bills you?
Step 3
Your estimate
A Culver City system
System size
6.6 kW
~15 panels
Saved per year
$3,359
at today's rates
Estimated cost
$36,645
solar + storage, installed
Payback
10.9 yrs
$102,835 over 25 yrs
Why the battery matters here. SCE runs NEM 3.0 net billing, which pays about $0.05 for a kilowatt-hour you export but charges up to $0.55 to buy one back at 6pm. Storing your own production instead of selling it adds roughly $1,645 a year on this bill. SGIP storage rebates may also apply in this territory.
Show the assumptions
Usage derived from $320/mo at SCE’s ~$0.36/kWh blended rate, giving 10,667 kWh a year.
Production at 5.4 peak sun hours a day with a 0.80 derate for inverter, wiring, soiling and heat losses: 10,407 kWh a year.
Self-consumption assumed at 88% of production; the remainder is exported at $0.05/kWh.
25-year figure compounds utility rates at 4.5% a year and degrades panel output 0.5% a year, net of system cost. Planning estimate only, not a quote.
Also in Culver City
More than panels
Neighborhoods we cover in Culver City
Carlson Park · Blair Hills · Hayden Tract · Fox Hills · and everywhere in between.
Culver City questions
Answered with local numbers
Specific to Culver City, SCE, and City of Culver City Building Safety.
How much does solar cost in Culver City?
A typical Culver City home paying around $300 a month to SCE needs roughly a 6.2 kW system, which lands near $19,712 installed before storage. Adding the 13.5 kWh battery we would normally pair with it brings the project to about $35,237. Roof type matters here: composition shingle and flat commercial is what we mostly see in Culver City, and that affects mounting hardware and labor.
Is solar worth it in Culver City with SCE?
Highest rates in the service area and the toughest export credits — which is exactly why a battery pays for itself fastest here. SCE customers also fund SGIP, so storage rebates are on the table. At 5.4 peak sun hours a day, a 6.2 kW array in Culver City produces roughly 9,713 kWh a year. Against SCE's approximate $0.36 per kWh, that is around $3,135 of annual value, putting simple payback near 11.2 years.
Who issues solar permits in Culver City?
Permits for Culver City go through City of Culver City Building Safety, and interconnection is handled separately by Southern California Edison. Those are two different clocks and they do not run in parallel by default. We file both and chase the corrections, which is usually where projects stall when homeowners manage it themselves.
Do you install batteries in Culver City?
Yes, and Culver City sits in SCE territory, so SGIP storage rebates may apply. Because SCE runs NEM 3.0 net billing, exported power earns roughly $0.05 per kWh while peak power costs up to $0.55 — storing your production rather than selling it is where the return comes from here.
How far is Culver City from your Northridge shop?
About 18 miles. That is comfortably inside our core service area, so surveys and service calls are quick to schedule.
Nearby
We also serve
Ready for a Culver City system design?
Send us one SCE bill. We will come back with a layout, a production model, and a real number.